[reSIProcate] Failed to build resip

[Daniel Pocock]

I've just patched configure to allow the db_cxx.h location to be 
specified in ./configure - this way repro is more likely to build.  
Debian is one platform that doesn't have db4/db_cxx.h, it is just 
/usr/include/db_cxx.h.  Previously, the compile would fail at 
repro/BerkeleyDb.hxx. 

Hope this change doesn't break configure for anybody else, I've 
defaulted it to the way it was.

I wasn't sure about the HAVE_CONFIG_H stuff in repro/BerkeleyDb.hxx so 
I've just ignored that

Jason Fischl wrote:

>If we see the question come up on the list frequently we can always do
>a minor dot release in a few weeks.
>
>Jason
>
>
>On 9/29/06, Robert Sparks <rjsparks at nostrum.com> wrote:
>  
>
>>No - leave it for post release.
>>
>>On Sep 29, 2006, at 11:22 AM, Byron Campen wrote:
>>
>>    
>>
>>>      Do we need to scrub them for this release? If so, would everyone
>>>tolerate the release differing from the last release candidate?
>>>
>>>Best regards,
>>>Byron Campen
>>>
>>>      
>>>
>>>>We should scrub those old artifacts away.
>>>>
>>>>RjS
>>>>
>>>>On Sep 29, 2006, at 9:58 AM, Byron Campen wrote:
>>>>
>>>>        
>>>>
>>>>>    If you want to make just rutil and resip, you need to ./
>>>>>configure in the top directory, and call 'make rutil resip'. The
>>>>>configure file in the resip directory appears to be from the old
>>>>>autotools build, which has not been maintained for some time.
>>>>>
>>>>>Best regards,
>>>>>Byron Campen
>>>>>
>>>>>          
>>>>>
>>>>>>-----BEGIN PGP SIGNED MESSAGE-----
>>>>>>Hash: SHA1
>>>>>>
>>>>>>   Hello!
>>>>>>   I want to build resiprocate stack on Debian GNU/Linux. I
>>>>>>checked-out
>>>>>>resiprocate-1.0-RC4. I want to build *ONLY* resip and rutil. I
>>>>>>tried to
>>>>>>build resip but "./configure" failed immediately:
>>>>>>
>>>>>>configure: error: cannot find sources (resiprocate/
>>>>>>config.hxx.in) in . or ..
>>>>>>
>>>>>>I edited configure script and replaced "resiprocate" with "stack".
>>>>>>"./configure" failed again:
>>>>>>
>>>>>>configure: error: cannot find install-sh or install.sh
>>>>>>in . ./.. ./../..
>>>>>>
>>>>>>If I comment out checks for install-sh/install.sh, configure
>>>>>>runs for a
>>>>>>while but fails to find a config.sub because $ac_aux_dir has no
>>>>>>value:
>>>>>>
>>>>>>configure: error: cannot run /bin/sh /config.sub
>>>>>>
>>>>>>   So, my question is: can I build resip and rutil separately or I
>>>>>>have to
>>>>>>build whole project (which I don't want)?
>>>>>>   Thanks in advance!
>>>>>>
>>>>>>   Best regards,
>>>>>>   Petyo Milotinov
>>>>>>-----BEGIN PGP SIGNATURE-----
>>>>>>Version: GnuPG v1.4.2.2 (MingW32)
>>>>>>Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
>>>>>>
>>>>>>iD8DBQFFHTHlmVNP4ZywRaQRAg1SAKCH5a7gIGQH5S6tygDR+35SQfOppwCcDuSK
>>>>>>8nggozFjKkW9xJX0nP2zi+4=
>>>>>>=FySS
>>>>>>-----END PGP SIGNATURE-----
>>>>>>_______________________________________________
>>>>>>resiprocate-devel mailing list
>>>>>>resiprocate-devel at list.sipfoundry.org
>>>>>>https://list.sipfoundry.org/mailman/listinfo/resiprocate-devel
>>>>>>            
>>>>>>
>>>>>_______________________________________________
>>>>>resiprocate-devel mailing list
>>>>>resiprocate-devel at list.sipfoundry.org
>>>>>https://list.sipfoundry.org/mailman/listinfo/resiprocate-devel
>>>>>          
>>>>>
>>_______________________________________________
>>resiprocate-devel mailing list
>>resiprocate-devel at list.sipfoundry.org
>>https://list.sipfoundry.org/mailman/listinfo/resiprocate-devel
>>
>>    
>>
>_______________________________________________
>resiprocate-devel mailing list
>resiprocate-devel at list.sipfoundry.org
>https://list.sipfoundry.org/mailman/listinfo/resiprocate-devel
>  
>